|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It is wonderful done!!! a great job in scanning the manual. Superior quality in all the electric scheme. Very understandable and net!!! Thank you!
 ;
muy buen manual por lo completo de este algunos esquemas estan muy divididos lo que hace algo dificil el seguimiento.
;
very good manual, with detail and clarity in esquematic diagrams and waveforms .
;
Very quality copy of original service manual, which contains the circuit diagrams, PCB and lists of components, well as recommendation for calibration procedures of device, also everything else, that need for repair, tuning and use this oscilloscope.
All presented copies have high-resolution, so you can view all in detail.
This manual will very useful for simple owners and for repairers.
I recommend these manual, because myself is owner of Philips PM3216 and I need sometimes servicing these oscilloscope (principally calibrating).
Also, these document is an example of excellent design of technical documentation.
;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
PA 2000 / PA 4000
9. REMOVE 35 SCREWS(A) ON THE CHASSIS-BACK(18) <6> INPUT P. C. BOARD(h) REMOVAL. 1. REMOVE THE CHSSIS-TOP(20), REFERRING TO THE PREVIOUS STEP<1> 2. REMOVE THE CHASSIS-BACK, REFERRING TO THE PREVIOUS STEP<5> 3. DISCONNECT THE CONNECTOR(CP2) FROM LEAD WIRE(CW102) ON THE INPUT P.C. BOARD(h) 4. DISCONNECT THE CONNECTOR(CP1) FROM LEAD WIRE(CW101) ON THE INPUT P.C. BOARD(h) 5. DISCONNECT THE CONNECTOR(CP2) FROM LEAD WIRE(CW2) ON THE INPUT P.C. BOARD(h) 6. DISCONNECT THE CONNECTOR(CP1) FROM LEAD WIRE(CW1) ON THE INPUT P.C. BOARD(h) 7. DISCONNECT THE LEAD WIRE(5P) FROM CONNECTOR(CP24, CP25) ON THE INPUT P.C. BOARD(h) 8. DISCONNECT THE CONNECTOR(CP9) FROM LEAD WIRE(CW9) ON THE MAIN P.C.BOARD(e) 9. DISCONNECT THE CONNECTOR (CP22, CARD-CABLE) ON THE INPUT P. C. BOARD(h) FROM CONNECTOR (CP 11) ON THE MICOM P. C. BOARD(f). 10. DISCONNECT THE CONNECTOR(CP13, CARDCABLE) FROM LEAD WIRE(CP12) ON THE MAIN P. C. BOARD(e) 11. REMOVE 6 SCREWS(D) AND THEN REMOVE THE INPUT P. C. BOARD(h) <7> MICOM P. C. BOARD(f) REMOVAL. 1. REMOVE THE CHSSIS-TOP(20), REFERRING TO THE PREVIOUS STEP<1> 2. REMOVE THE CHASSIS-BACK, REFERRING TO THE PREVIOUS STEP<5> 3. REMOVE THE INPUT P. C. BOARD, REFERRING TO THE PREVIOUS STEP<6> 4. REMOVE 3 SCREWS(D) AND THEN REMOVE THE MICOM P. C. BOARD(f) <8> RADIATOR ASS'Y(AB) REMOVAL(RIGHT SIDE). 1. REMOVE THE CHSSIS-TOP(20), REFERRING TO THE PREVIOUS STEP<1> 2. REMOVE THE FRONT-PANEL ASS'Y(AA), REFERRING TO THE PREVIOUS STEP<2> 3. REMOVE THE CHASSIS-FORNT, REFERRING TO THE PREVIOUS STEP<3> 4. REMOVE THE CHASSIS-SIDE, REFERRING TO THE PREVIOUS STEP<4> 5. REMOVE THE CHASSIS-BACK, REFERRING TO THE PREVIOUS STEP<5> 6. DISCONNECT THE CONNECTOR(CP104) ON THE MAIN P. C. BOARD(e) FROM CONNECTOR(CW4-1, CW4-2) ON THE AMP P. C. BOARD(d) 7. DISCONNECT THE CONNECTOR(CP8) ON THE MAIN P. C. BOARD(e) FROM POSSITOR ON THE RADIATOR. 8. DISCONNECT THE CONNECTOR(CW9, 2P) ON THE MAIN P. C. BOARD(e) FROM CONNECTOR(CP9-1/3) ON THE AMP P. C. BOARD(d) 9. DISCONNECT THE CONNECTOR(CP103) ON THE MAIN P. C. BOARD(e) FROM CONNECTOR(CW3) ON THE AMP P. C. BOARD(d) 10. REMOVE 3 SCREWS AND THEN PULL OUT THE RADIATOR ASS'Y(AB) <9> RADIATOR ASS'Y(AB) REMOVAL(LEFT SIDE). 1. REMOVE THE CHSSIS-TOP(20), REFERRING TO THE PREVIOUS STEP<1>
9
|
|
|
> |
|
